Fermax 5293 KEYPAD W/RESISTANT PROXIMITY

Anti-vandal keypad with integrated proximity, narrow profile and small dimensions. It allows working in autonomous or centralized mode.

STANDALONE MODE WITH INTEGRATED CONTROLLER (default)

Maximum capacity of up to 600 users.

Dispose of:

2A relay output configurable from 1-99s (5s by default) or bistable (when the card is presented, the relay is activated and when it is presented again, it is deactivated).

Open door sensor input.

Exit button input.

- Alarm Output- (negative output that allows activating a relay ref.2013).

This keyboard allows up to 4 different types of access:

card only

Card+PIN.

Card or PIN (default)

Multicard, PIN.

Presenting 2 to 9 valid cards or pins will open the door. Entering the access code is done by entering the 4 to 6 digit code + #. Multicard/PIN type access allows the user to always be accompanied. For example, if it is programmed with 3 identifiers, in order to activate the door, the user will be there with his valid card and until the two additional cards pass (example of the guards), the door will not open. Each user is associated with an identifier number called ID (1-600). Users with ID (1-598) are standard users who upon presentation of a valid card or code will open the door. Users with ID (599 or 600) are panic users. When presenting their card or valid code, these users open the door and simultaneously activate the auxiliary output Alarm- for 1 minute or until a valid card or pin is presented.

The keypad has a door sensor input (can be enabled or disabled). If it is activated and the door is opened without prior authorization, an alarm will go off until a valid identifier is presented and the door is closed. It will also activate an alarm, if the door is left open for more than 1 minute, after a valid access.

The keypad is supplied with two master cards that allow registering or deleting cards or key rings, not codes. The codes are registered through the keyboard itself.

STAND-ALONE MODE WITH EXTERNAL CONTROLLER

If a user capacity between 600-1000 is needed, it is possible to configure the keyboard as wiegand26 and connect it to an autonomous MINI controller ref. 5276.

CENTRALIZED MODE

To access the user database on a PC or allow access to more than 600 people, this keyboard can be configured in Wiegand 26/8bits burst so that it can be installed in a centralized system such as AC-MAX, AC+ or IP -AXES, which will allow you to have a record of inputs and outputs knowing time, user and access. To carry out this type of installation, it is necessary to add an external controller to the reader, which will be managed by a PC and will be able to have the user database and view the event log in real time or offline.

Technical specifications

MECHANICAL CHARACTERISTICS

APPEARANCE

3mm aluminum

Surface fixing system.

hidden screws.

IP66

DIMENSIONS

Surface mount (55(H) x 147(V) x 20(P) mm.

TECHNICAL CHARACTERISTICS

Feeding:

12-28 Vac/dc

Centralized: 12Vdc.

Standby consumption:

12Vdc / 65mA

Operating temperature: [-20ºC, +60ºC]

Humidity: [10%, 90%]

Compatibility: EM (125KHz), MIFARE (13.56MHz) and HID (ISOProxII, 125KHz) cards/keychains

Configurable in Wiegand 26 proximity protocol and 8-bit burst keyboard format.

Relay (stand-alone) 2A (C, No, Nc)

RF radiated power: 125KHz: 4.382dBuA/m, 13.56MHz: 2.02dBuA/m.

TECHNICAL SPECIFICATIONS

STAND-ALONE WIRING (with integrated controller)

~ (Red): Positive supply 12~28Vca/dc

~- (Grey&black): Negative supply 12~28Vca/dc

C (White&black),NO (Blue),NC (Green&black): Potential free relay. C_common, NO_Normally open, NC_Normally closed.

GND (Black), SP (Brown): door sensor

GND (Black), BS (Yellow): hall exit button

Alarm- (Gray), ~(Red): alarm output <200mA

CENTRALIZED WIRING

+ (Red): Positive 12Vdc supply

(Black): Negative 12Vdc supply

DT (D0) (Green), CK (D1) (White): Wiegand26 connection

G (LED) (Brown): LED control.

Buzz (Beep) (Yellow): acoustic signal.